My Cart (0) - $0.00
You have no items in your shopping cart.

0

Welcome To CleanFreak.com

888-722-5508
Se Habla Español

buffing

OBJECTIVE:

To strip old layers of floor finish, or wax, from commercially tiled floors.

 

1Prep Area -

Remove all obstacles and furniture from the area. Set up an area of about 200 to 400 square feet. This will be the area you start with. Cordon off the entire area that needs to be stripped by setting up the necessary caution/wet floor signs. Create an area for exiting the stripping area. Place mats down to remove protective footwear and avoid tracking stripping materials to other parts of the buildings. Follow the dust mopping procedure to remove all debris, dirt, and large objects (i.e. pallet chips), from the area.

2Prep Stripping Materials -

. Mop bucket lined with trash bag, high density 10-15 gallon trash bags

Line a mop bucket with a plastic liner, similar to something like our  This will keep the stripper contained and not allow it to enter the bucket area. The mop bucket can then to be used for future mopping purposes, and not just relegated to stripping jobs. Consult the necessary MSDS sheets for the stripping solutions, so you are properly acquainted with the hazards associated with the chemicals you'll be using. Take the pre-determined stripping solution and pour it into the lined bucket.We offer a super concentrated floor wax stripper, where the 1 quart bottle needs to be mixed with 5 quarts of hot water. That product is concentrated, so it needs to be mixed with water. Most solutions are used at full strength, you'll need to consult the label on your specific product to be certain. Put on the necessary safety clothing, like our disposable plastic shoe covers or floor stripping protective bootsface masks/respiratorsnitrile gloves and safety glasses.

3Apply Stripping Solution -

Easy Lift floor wax stripper.

You'll want to sufficiently cover the 200 to 400 square foot area you already set up. Apply generous amounts of solution with a mop and let it sit for a few minutes to loosen the floor finish before continuing to the next step. Do not allow the stripper to dry.

Take the specified floor stripping pad and attach it the pad driver on your floor buffer or auto scrubber. Auto scrubbers are often the popular choice for stripping, because they can then be used to recover the stripping solution. If you are using an auto scrubber, leave the squeegee up and scrub the area once completely before putting the squeegee down and scrubbing again while at the same time, recovering the solution. If you are using a rotary floor scrubber, start in the opposite corner of your walk off mat, and slowly move towards that area. Some areas will require several passes to strip the floor completely of the old floor wax. A black utility stripping pad may be needed to properly get into corners and up against baseboards. A baseboard stripper/cleaner may also be needed to properly clean the baseboards.

4Pick Up Dirty Solution -

Wet stripper vacuum.

If you are using an auto scrubber, after a few passes of just scrubbing, lower the squeegee, and recover all the stripping solution while continuing to scrub. If a floor buffer is your stripping machine of choice, you'll need to use a certified wet recovery vacuum that is specialized for stripper recovery like our wet stripper vac, which has a front mount recovery squeegee. You'll want to pick up this solution immediately after scrubbing, as you don't want this solution to dry on the floor.

5Rinse And Dry Floor -

Use a fresh mop bucket, or remove the liner from the mop bucket you were using and fill it with clean water. Add 1-2 ounces of floor stripping neutralizer per gallon of water. You can also use your auto scrubber or floor buffer mounted with a solution tank to accomplish this. Just make sure to use a different scrub brush or pad than the one you used to strip the floor. Mop/scrub entire area with the neutralizer/water combination to try and neutralize as much of the alkaline in the stripper as possible. If the floor is not at a neutral state when placing your floor finish down, it will not adhere properly. Wipe down all basebaords and corners to assure all stripping solution is removed. Rinse the floor one or two more times with just clean water to ensure that all stripping solutions are recovered.

6Clean Up -

3 speed air mover, floor dryer.

All solution tanks, mops, mop buckets, squeegees and hoses must be thoroughly rinsed and cleaned out. If the stripping solution or stripped material, otherwise know as slurry is allowed to sit in the tanks, it can dry or start to solidify and ruin the machinery.

All flooring areas need to be completely dry before moving onto the next step of applying floor finish. We recommend using a floor drying fan like our 3-speed floor dryer to ensure all areas are completely dry.


The most basic janitorial & custodial procedures

Please wait...

Close
Yup, this was just added to your cart!

Added to Cart


SKU:
Price: $0.00

Cart Summary


$0.00

{{var product.name}} was removed from your cart


Continue shopping
View Cart